Products
34 products
Sort by:
34 products
Aluminum finish — a clean, professional transition at every outside corner
Designed exclusively for EUBIQ's SH1 ducting, this fixed 90° outside corner is made of plastic with an aluminum finish. It provides a neat junction at an outside corner while maintaining visual consistency with your ducting.
Why choose a dedicated corner?
Designed for SH1 ducting
A dedicated piece for the SH1 profile to create the transition between two sections at an outside corner.
Cable routing
Follows the cable path around a change in direction. Check their positioning and ensure there are no deburred cut edges during installation.
Snap-fit installation
Snaps onto SH1 ducting sections. No special tools are required for installation in most configurations.
Aluminum finish
An aluminum appearance that matches the installation. The piece is made of plastic, not aluminum.
DIY cut vs. original corner
- Requires preparing and trimming the cuts
- Edges must be carefully deburred
- Joint precision depends on the quality of the cut
- Requires finishing work at the change in direction
- Dedicated piece for the SH1 profile
- Fixed 90° outside corner
- Snap-fit installation
- Plastic with aluminum finish
Technical specifications
This corner is intended exclusively for SH1 ducting. Check your ducting reference carefully before purchasing.
In what contexts should it be used?
Workstations and offices
Manage the routing of IT and electrical cables around a partition or furniture corner.
Workshops and technical spaces
Route around the protruding corners of a room with a dedicated junction for your SH1 ducting.
Residential installations
Create an outside corner in a living room, bedroom, or hallway with a discreet finish that matches the ducting.
Commercial premises
Maintain a neat appearance in spaces visible to customers or the public.
4-step installation guide
Cut your ducting sections
Ensure that your two SH1 ducting sections are cut correctly at 90° (straight cut, not mitered).
Position the corner
Snap the SH1 outside corner onto the end of each section. The piece is designed to fit without force.
Check the alignment
Visually check that the two ducting sections are properly aligned and that the corner is correctly applied against the wall surface.
Secure if necessary
Depending on your configuration, secure the ducting to the wall according to the SH1 range recommendations and the characteristics of the support surface.
Plastic and aluminum finish: two distinct pieces of information
The piece is made of plastic. Its aluminum finish does not mean it is made of metal.
The aluminum finish complements the appearance of your SH1 installation.
A discreet transition at the outside corners of your ducting run.
Frequently asked questions
Is this corner compatible with other EUBIQ ducting?
No. It is designed specifically for SH1 ducting. For other references in the range, check the compatible accessories listed on each product sheet.
Is it made of aluminum?
No. It is made of plastic and has an aluminum finish. It is not a solid aluminum piece.
Can the angle be set to anything other than 90°?
No, this corner is fixed at 90°. Check that this geometry matches your installation.
Do I need to buy an inside corner as well?
This depends on your ducting run. The outside corner is for a protruding corner. For an inset corner, you need a suitable inside corner.
Is this accessory sold individually?
Yes, it is sold individually. Allow one corner per outside corner of your installation.
Additional information
A neat transition for your SH1 installation.
Plastic, aluminum finish · Fixed 90° outside cornerAdd to cart
A neat transition at every inside corner
Designed for EUBIQ's SH1 trunking, this fixed 90° inside corner angle allows you to create a junction in an inside corner. Made of plastic, it is available in an aluminum or matte black finish to match your installation.
Why choose a dedicated angle?
Designed for SH1 Trunking
A dedicated piece for the SH1 profile to create the transition between two trunking sections in an inside corner.
Cable Routing
Follows the cable routing around the change of direction. Check their positioning and the absence of unburred cut edges during installation.
Snap-Fit Installation
Snaps onto SH1 trunking sections to create a 90° junction in an inside corner.
Two Finishes
Choose the aluminum or matte black finish depending on the desired variant. The finish describes the appearance of the part, not its plastic material.
DIY Cut vs. Dedicated Angle
- Requires preparing and adjusting the cuts
- Edges must be carefully deburred
- Joint precision depends on the quality of the cut
- Requires finishing work at the change of direction
- Dedicated piece for the SH1 profile
- Fixed 90° inside corner angle
- Snap-fit installation
- Aluminum or matte black finishes
Technical Specifications
This angle is designed exclusively for SH1 trunking. Check your trunking reference, the finish, and the corner geometry before ordering.
In what contexts should it be used?
Workstations and Desks
Extend your SH1 route in an inside corner to follow the cable routing of the installation.
Workshops and Technical Areas
Create a dedicated junction at the inside corners of your trunking route.
Residential Fit-outs
Create a neat transition in the inside corners of a room by choosing a finish that matches your trunking.
Commercial Premises
Maintain a consistent appearance in offices, reception areas, or commercial premises.
5-Step Installation Guide
Position the first SH1 section
Prepare the length of trunking and position it along the wall up to the inside corner, according to the mounting instructions.
Snap in the inside corner angle
Present the angle at the end of the first section and snap it in without forcing it.
Connect the second section
Insert the second section into the other opening, perpendicular to the first, to follow the inside corner.
Check alignment and fastening
Check the fit of the elements and secure the trunking according to the SH1 range recommendations and the characteristics of the support.
Check cable routing and closure
Check the cable routing before completing the assembly according to the system documentation. Any work on the electrical installation must be carried out without power by a qualified electrician.
Material and Finishes
Plastic Material
The part is made of plastic. The aluminum finish does not mean it is made of metal.
Aluminum Finish
An aluminum appearance to visually complete your SH1 installation.
Matte Black Finish
A second finish offered on this product sheet, to be selected according to the desired appearance.
Frequently Asked Questions
What is the difference between an inside and outside corner angle?
The inside corner angle corresponds to an inside corner, where the walls form a recess. The outside corner angle goes around a protruding corner. The two parts are not interchangeable.
Is it compatible with other trunking?
It is designed specifically for EUBIQ's SH1 trunking. Do not assume compatibility with another profile, even one with similar dimensions.
Is it made of aluminum?
No. Its material is plastic. The available finishes are aluminum and matte black.
Is the angle adjustable?
No. It is fixed at 90° and is suitable for inside corners matching this geometry.
How do I choose the finish?
Select the Alu or Black variant depending on your trunking and the other accessories, to maintain visual consistency.
Additional Information
A neat transition in the inside corners of your SH1 installation.
Fixed 90° inside corner angle · Aluminum or matte black finishes
The modular accessory that frees up your worktop
Designed for the EUBIQ SH1 profile, whether used as a rail or trunking, this 400 mm bar combines translucent plastic fasteners with an aluminium support. It allows you to hang spatulas, ladles and utensils under your SH1 profile, without screws or additional drilling.
Why choose this support bar?
Designed for the SH1 profile, whether used as an electrical rail or modular trunking. It snaps into place without additional screws.
Hang spatulas, ladles, tongs and other utensils within easy reach. Free up your drawers and worktop.
The fastening part is made of translucent plastic; the support bar is made of aluminium. The accessory is therefore not entirely made of aluminium.
Combine it with other SH1-compatible EUBIQ accessories: shelves, storage and electrical outlets. The profile adapts to your needs.
Technical specifications
Installation in 3 steps
Slide the translucent plastic fasteners into the slots provided on the EUBIQ SH1 profile, whether used as a rail or trunking.
A simple click is all it takes to hold the bar firmly in place, without screws or additional drilling.
Hang hooks, spatulas, ladles or tongs directly on the bar. Your worktop is now free!
Tip: For even more effective organisation, combine several compatible accessories from the EUBIQ SH1 system: shelves, storage and electrical outlets.
Who is this support bar for?
Want to organise your kitchen effectively? This bar complements your SH1 profile, whether used as a rail or trunking.
The EUBIQ SH1 modular system allows you to offer a functional layout tailored to your customers' needs.
- For kitchens equipped with an EUBIQ SH1 profile, as a rail or trunking
- To optimise the space above the worktop
- Suitable for kitchens with limited floor or worktop space
- Compatible with standard kitchen bar hooks and accessories
Frequently asked questions
Yes. It is suitable for the EUBIQ SH1 profile in both configurations: electrical rail or modular trunking. It is not designed for standalone use.
No. The fastening part is made of translucent plastic, while the support bar is made of aluminium.
No, no additional drilling is required for the bar itself. It snaps directly onto the already installed SH1 profile.
It is designed to support common kitchen utensils (spatulas, ladles, tongs, etc.). For information on the maximum permissible load, please refer to the EUBIQ technical documentation.
Yes, you can position and combine several bars depending on the length of your SH1 profile and your needs.
Technical documentation
This accessory is a fit-out and organisation product. It does not constitute electrical safety equipment. For any work on the electrical installation, please consult a qualified electrician.
No more cluttered worktops: your utensils are within easy reach, suspended on an aluminium support with translucent plastic fasteners.
A small accessory, a big difference in everyday life.
Add to cart
150 cm — Exclusively compatible with SH1 profile
Organize the routing of your cables in the EUBIQ SH1 cable duct with this 150 cm separation barrier. It creates a physical separation between the cable routing areas for power cables and data cables.
Two wiring areas in the SH1 profile
Physical separation
The barrier helps define the cable routing areas inside the SH1 duct.
Organized routing
Power cables and signal cables have separate routes, for a clearer installation.
Accessory designed for the SH1
Its shape is adapted to this EUBIQ profile. Check the reference of your duct before ordering.
EUBIQ barrier specifications
Adjust to the useful length of the route if necessary.
Designed specifically for the EUBIQ SH1 duct.
Installation in 5 steps
Prepare your duct
Check the mounting of the SH1 profile and prepare the installation area according to the system documentation. Any work on the electrical installation must be carried out when de-energized by a person qualified in electricity.
Adjust the length if necessary
For a section shorter than 150 cm, measure the useful length then adjust the barrier with a suitable tool. Hold the piece, follow the tool's safety instructions and deburr the cut.
Insert the barrier
Position it in the designated location of the SH1 profile, in accordance with the system documentation, to define two routing areas.
Distribute the cables
Organize the power cables and signal cables on either side of the separation, according to the requirements applicable to the installation.
Check then close
Check the positioning of the barrier and the cables before closing the profile with the appropriate elements.
For which projects?
Professional premises
Organization of cabling in the SH1 routes of offices, workstations and professional premises.
Residential developments
Organized routing of power and data cables in home SH1 installations.
Technical specifications
| Characteristic | Value |
|---|---|
| Brand | EUBIQ |
| Length | 150 cm |
| Dimensions (L × W × H) | 150 × 2 × 1 cm |
| Indicated weight | 150 g |
| Compatibility | Exclusively SH1 profile |
| Use | Power / low-voltage separation |
| Installation | Snap-in into the profile |
Frequently asked questions
What length is supplied?
The barrier measures 150 cm. Its dimensions are 150 × 2 × 1 cm.
Can the length be adjusted?
Yes. For a section shorter than 150 cm, measure the required length then make a clean cut with a suitable tool, following its safety instructions. Deburr before installation.
Is it compatible with other profiles?
This barrier is designed exclusively for the EUBIQ SH1 profile. For another model, check the reference of the corresponding separator.
How is the barrier installed?
By snapping it into the designated location of the SH1 profile, without screws or glue for the barrier itself. An eventual cut requires a suitable tool.
Is the barrier sufficient to validate the installation?
No. This accessory defines the routing areas in the duct. The entire cabling and its implementation must still be checked by a person qualified in electricity.
Important note: the barrier is a physical separation accessory. It does not constitute a certification of conformity of the installation, nor a guarantee of absence of interference or compartment sealing.
An organized SH1 route, with distinct wiring areas.
EUBIQ separation barrier · Length 150 cm · SH1 profile
The pair — a neat finish at both ends of the profile
Close the open ends of your EUBIQ RH2 raceway with this pair of dedicated end caps, supplied with fixing screws. They conceal the opening of the profile to neatly finish your installation recessed into furniture, particularly desks and large conference tables.
Why choose dedicated end caps?
Closes the ends
They close the open ends of the RH2 raceway and conceal the interior of the profile at the start and end of the run.
Designed for RH2
Accessories designed for the RH2 profile, to be selected according to the raceway model in your installation.
Sold in pairs, screws included
Two end caps with their fixing screws. Count the open ends to be finished to determine the quantity required.
Two finishes
Choose Aluminium or Black depending on the desired variant and the appearance of your installation.
End cap or SFC2D blanking plate?
SFC2D blanking plate
Closes the non-electrified longitudinal sections of the raceway. It completes areas equipped with SFC3 electrical segments.
RH2 end cap
Closes the end of the profile. It does not replace the SFC2D or the components of the electrified sections.
Technical specifications
To finish your RH2 installation
Desks and workstations
Finish the ends of RH2 profiles recessed into furniture.
Large conference tables
Complete the finish of your RH2 run by assembling it with the appropriate components.
Preparing the run finish
Identify the open ends to be closed, check the chosen finish, then fix the end caps with the screws supplied, according to the RH2 documentation. An installation containing several independent lengths may require several pairs.
The RH2 is designed to be recessed into furniture. These end caps close the ends of the profile; they do not change its protrusion height and do not indicate the watertightness of the assembly. Any work on the electrical installation must be carried out while disconnected from the power supply by a person qualified in electrical work.
Frequently asked questions
What are these end caps used for?
They close the open ends of the RH2 raceway to conceal the interior of the profile and complete the presentation of the installation.
Are they sold individually?
No, they are sold in pairs, i.e. two end caps, with fixing screws included.
How are they fixed?
RH2 end caps are fixed by screwing. The screws required for their fixing are supplied with the pair.
What is the difference with SH1 end caps?
The role is the same, but each end cap must be chosen for the profile concerned. This data sheet presents the end caps designed for the RH2.
What is the difference with the SFC2D?
The SFC2D closes a non-electrified longitudinal section. The end caps close the ends of the profile. These functions are distinct.
What finishes are available?
Aluminium and Black, depending on the selected variant.
A neat RH2 installation right to the ends.
The pair · Fixing screws included · Aluminium or Black finishes · RH2 raceway
The pair — a neat finish at both ends of the track
Close the open ends of your EUBIQ SH1 trunking with this pair of dedicated end caps. They screw onto the profile to conceal its opening and provide a neat finish to the installation. Screws and screw caps are included with the pair. Choose the Aluminium or Black finish depending on the desired variant.
Why choose dedicated end caps?
Closes the ends
They close the open ends of the SH1 trunking and conceal the inside of the profile at the start and end of the track.
Designed for the SH1 profile
Components designed for this trunking model, distinct from accessories intended for other profiles.
Screw-on mounting
The end caps screw onto the ends of the SH1 trunking. Screws and screw caps are included with each pair.
Two finishes
The Aluminium and Black variants allow you to choose a finish that matches your trunking and other accessories.
End cap or other finishing element?
- The SFC2D closes non-electrified longitudinal sections
- Connectors are intended for track junctions
- Angles allow for changes in direction
- These elements do not replace end caps
- Close the open ends of the profile
- Finish the start and end of the track
- Screw onto the SH1 trunking
- Sold as a pair, with screws and screw caps included
Technical specifications
Check your trunking reference and the finish before ordering. Closing the ends does not indicate that the entire assembly is watertight.
To finish your SH1 installation
Residential settings
Neatly finish the visible ends of an SH1 track in your home.
Offices and workstations
Finish the lengths of trunking used in your custom installation.
Commercial premises
Maintain a consistent appearance with other SH1 accessories in workspaces and commercial premises.
3-step installation guide
Prepare the SH1 trunking
Check that the profile is securely fixed and that the components and cables are correctly positioned, according to the installation documentation.
Screw on the end caps
Position one cap at each end to be closed and secure it with the screws provided. Follow the SH1 system assembly instructions.
Fit the screw caps and check the finish
Fit the screw caps provided, then check that the end caps are properly fitted and secure. All work on the electrical installation must be carried out without power by a qualified electrician.
One pair for two ends
The package contains two end caps, screws and screw caps. Identify the open ends to be closed on your SH1 track to determine the quantity required. A track with several independent lengths may require several pairs.
Frequently asked questions
What are these end caps used for?
They close the open ends of the SH1 trunking and conceal the inside of the profile for a neat finish.
Are they sold individually?
No. They are sold as a pair, meaning two end caps, with screws and screw caps included. Count the open ends of your track to determine the quantity required.
Are they compatible with other trunking?
They are designed exclusively for the EUBIQ SH1 trunking. For another model, choose the end caps designed for the relevant profile.
How do they differ from the SFC2D?
The SFC2D closes a non-electrified longitudinal section. The end cap closes the end of the profile. The two elements have different functions.
How are they fixed?
They screw onto the ends of the SH1 trunking. Screws and screw caps are included with each pair. They are not simply snapped into place.
What finishes are available?
The available variants are Aluminium and Black. Select the one that matches your trunking and other accessories.
Additional information
A neat SH1 installation right to the ends.
The pair · Screw-on mounting · Screws and screw caps included · Aluminium or Black finishes
A coiled cord that connects directly to all Eubiq rails. Its extended length is 2.4 m and the cable ends with an IEC C13 connector. Electrical specifications: 220 V and 16 A. The red indicator light shows when power is supplied.
A cord for your connection
The CCS13 comes with a black coiled cable, unlike the PLT16, which is a cableable plug. It connects directly to all Eubiq rails and offers a cable length of 2.4 m when extended. The number 13 in its reference corresponds to its IEC C13 termination.
Technical specifications
| Model | CCS13 |
| Type | Coiled cord |
| Brand | EUBIQ |
| Reference | 2038-0002-0412 |
| Voltage | 220 V |
| Current | 16 A |
| Indication | Red power-on indicator light |
| Cable | Black coiled |
| Extended cable length | 2.4 m |
| Cable termination | IEC C13 |
| Indicated dimensions (L × W × H) | 32 × 14 × 1 cm |
| Connection | All Eubiq rails |
Compatibility and connection
Eubiq cords, including the CCS13, as well as the PLT16 cableable plug, are compatible with all Eubiq rails. Check that the IEC C13 termination matches the connector of the equipment to be connected. Respect the electrical specifications of the cord and the manufacturer's instructions.
Frequently asked questions
What does the number 13 mean?
The number 13 in CCS13 corresponds to the IEC C13 cable termination. Similarly, CCS5 designates an IEC C5 "Mickey" termination and CCS7 an IEC C7 termination.
What is the red indicator light for?
The red indicator light shows when power is supplied to the cord.
What is the difference with the PLT16?
The PLT16 is a cableable plug. The CCS13 comes with a black coiled cable, with an extended length of 2.4 m, ending in IEC C13. Both are compatible with all Eubiq rails.
What are the electrical specifications?
220 V and 16 A.
Does the length of 2.4 m correspond to the extended cable?
Yes, 2.4 m is the length indicated when the coiled cable is extended.
What does it connect to?
The CCS13 connects directly to all Eubiq rails.
Follow the documentation for the cord and the rail. For any work on the installation wiring, consult a qualified electrician and work with the power turned off.
A coiled cord that connects directly to all Eubiq rails. Its extended length is 1.2 m. The cable ends with an IEC C5 "Mickey" connector. Electrical specifications: 220 V and 16 A. The red indicator light shows when power is supplied.
A cord for your connection
The CCS5 comes with a black coiled cable, unlike the PLT16, which is a cable-mount socket. It connects directly to all Eubiq rails and offers an extended cable length of 1.2 m.
Technical specifications
| Model | CCS5 |
| Type | Coiled cord |
| Brand | EUBIQ |
| Reference | 2040-0002-0412 |
| Voltage | 220 V |
| Current | 16 A |
| Indication | Red power-on indicator light |
| Cable | Black coiled |
| Extended cable length | 1.2 m |
| Indicated dimensions (L × W × H) | 32 × 14 × 1 cm |
| Cable termination | IEC C5 "Mickey" |
| Connection | All Eubiq rails |
Compatibility and connection
Eubiq cords, including the CCS5, as well as the PLT16 cable-mount socket, are compatible with all Eubiq rails. Observe the CCS5's 220 V and 16 A specifications as well as the manufacturer's instructions for the equipment to be connected.
Frequently asked questions
What does the number 5 mean?
The number 5 in CCS5 corresponds to the IEC C5 cable termination, also known as "Mickey", as with the CSP5-15.
What is the red indicator light for?
The red indicator light shows when power is supplied to the cord.
How does it differ from the PLT16?
The PLT16 is a cable-mount socket. The CCS5 is a cord with a black coiled cable that has an extended length of 1.2 m. Both are compatible with all Eubiq rails.
What are the electrical specifications?
The CCS5 is designed for a voltage of 220 V and a current of 16 A.
Does the 1.2 m length refer to the extended cable?
Yes, 1.2 m is the length when the coiled cable is extended.
What does it connect to?
The CCS5 connects directly to all Eubiq rails.
Follow the documentation for the cord and the rail. For any work on the installation wiring, consult a qualified electrician and work with the power turned off.
Showing 8/34
NextCollections featured
The French specialist in designer electrical tracks since 2008. Exclusive Eubiq importer in Europe — Dilectro Ltd.
The French specialist in designer electrical tracks since 2008. Exclusive Eubiq importer in Europe — Dilectro Ltd.